Bluetooth Shield for Arduino

From LinkSprite Playgound
Revision as of 22:37, 25 May 2013 by Jingfeng (talk | contribs) (Bluetooth shield communicates to Android Smartphone)
Jump to: navigation, search

Introduction

The Bluetooth Shield integrates a Serial Bluetooth module. It can be easily used with Arduino for transparent wireless serial communication. You can choose two pins from Arduino D0 to D7 as Software Serial Ports to communicate with Bluetooth Shield (D0 and D1 is Hardware Serial Port). The shield also has two Grove connectors (one is Digital, the other is Analog) for you to install Grove modules.


Note: The Shield may not be compatible with some Bluetooth capable devices, like some HTC mobile phone (G7 with Android 2.33) and Apple devices with special profile on Bluetooth function.

Bluetooth shield.jpg

Features

  • Arduino compatible
  • Up to 10m communication distance for line-of-sight communication
  • UART interface (TTL) with programmable baud rate (SPP firmware installed)
  • Default Baud rate: 38400, Data bits: 8, Stop bit: 1, Parity: No parity
  • Default PINCODE:”0000”
  • A full set of configuration commands
  • On board PCB Antenna

Specification

Item Min Typical Max Unit
Voltage 2.8 3.3 3.5 VDC
Current 3 / 100 mA
Communication Distance(in house) / / 10 m
Protocol Bluetooth V2.0 with SPP firmware /
Interface Uart Serial Port(TTL) /
Supported Baudrate 9600, 19200, 38400, 57600, 115200, 230400, 460800 bps
Dimension 57.4x45.3x19.4 mm
Net Weight 10±2 g

Quick Test

Host-Slave mode: Communication between two different Bluetooth shields

[Note: in the following sample code, the soft serial has a baud rate of 38400, which makes the code a little bit not stable, if you see failure, please try multiple times].

  • Take one Bluetooth shield and do the following:
Select the Bluetooth shield communication port using jumpers: BT_RX is connected to D6 of Digital-6, BT_TX is connected to Digital-7. Move the mode selection switch to lower position so that Bluetooth module will enter into AT command mode.

Bluetoothshield host slave 1.jpg

Install Bluetooth shield on the Arduino Uno,and plung Arduino into PC, LED D1 on Bluetooth shield will start blinking.
Copy and paste the following sample code and download to Arduino:

<syntaxhighlight lang="c">

  1. include <SoftwareSerial.h>
  2. define RxD 7
  3. define TxD 6

SoftwareSerial BlueToothSerial(RxD,TxD); void setup() {

  Serial.begin(38400);     
  BlueToothSerial.begin(38400); 
  delay(500);

} void loop() {

   if(BlueToothSerial.available())
   {
     Serial.print(char(BlueToothSerial.read()));
   }
   if(Serial.available())
   {
     BlueToothSerial.print(char(Serial.read()));
   }	    

}

</syntaxhighlight>

Launch X-CTU, select the corresponding port, configure the baud rate to be 38400/0/8/N/1. LED-D1 on Bluetooth shield will turn on for about 1 second and turn off.

Bluetoothshield host slave 2.jpg

Send AT command through the UART to check MAC address of the Bluetooth shield ("AT+ADDR?\r\n"), and write down the results. In the following picture, we show that the MAC address is: 12:11:230317.

Bluetoothshield host slave 3.jpg

In X-CTU, close com port. Now, we download the slave code as shown below:

<syntaxhighlight lang="c">

  1. include <SoftwareSerial.h>
  2. define RxD 7
  3. define TxD 6

SoftwareSerial BlueToothSerial(RxD,TxD); char flag=1; void Test_BlueTooth() {

  unsigned char t=0;
  String RXD = "";
  Serial.println("Test BlueTooth ...");
  BlueToothSerial.print("AT\r\n");  
  delay(100);
  while(BlueToothSerial.available()>0)
  {    
     RXD +=  char( BlueToothSerial.read() );
     delay(1);
  } 
  do{
    t++;
    delay(400);
    Serial.println("Test Failed ! Retrying ...");
  }while( ((RXD[0]!='O')&&(RXD[1]!='K'))&&(t<5));  
  if(t<5) Serial.println("Test Successful !\r\n");
  else { Serial.println("Retry Failed !"); while(1); }

}

void sendBlueToothCommand(char *Command) {

 BlueToothSerial.print(Command);
 Serial.print(Command); 
 delay(100);
 while(BlueToothSerial.available())
 {    
    Serial.print(char(BlueToothSerial.read())); 
 }

}

void setupBlueTooth() {

 Serial.println("Bluetooth Initialization ...");      
 sendBlueToothCommand("AT+NAME=Slave\r\n");
 sendBlueToothCommand("AT+ROLE=0\r\n");
 sendBlueToothCommand("AT+CMODE=1\r\n");
 sendBlueToothCommand("AT+PSWD=1234\r\n");
 sendBlueToothCommand("AT+UART=38400,0,0\r\n");
 delay(500);
 Serial.println("Bluetooth Initialized Successfully !\r\n");
 do{
   if(Serial.available())
   {
     if( Serial.read() == 'S')
     {
       sendBlueToothCommand("AT+RESET\r\n");
       flag = 0;
     }
   }
 }while(flag);

}

void setup() {

  Serial.begin(38400);     
  BlueToothSerial.begin(38400); 
  delay(500);
  Test_BlueTooth();  
  setupBlueTooth();

}

void loop() {

   if(BlueToothSerial.available())
   {
     Serial.print(char(BlueToothSerial.read()));
   }
   if(Serial.available())
   {
     BlueToothSerial.print(char(Serial.read()));
   }	    

}


</syntaxhighlight>

Go back to X-CTU, and open the com port again. The baud rate setting is still 38400/0/8/N/1. Now the LED D1 on bluetooth shield will start blinking at a period of around 2 seconds. At the same time, the serial port will output something like the following:

Bluetoothshield host slave 4.jpg

Now we move the mode switch the upper position, which is 'NC'. Send upper case 'S', and the bluetooth module will enter into normal mode, and LED-D1 will start blinking at a frequency of once per 0.2 second, which means that Bluetooth module has finished the initialization.

At the same time, the following will show up on serial terminal:

Bluetoothshield host slave 5.jpg

  • Now, let's take another Bluetooth shield.
Install it in Arduino, and plug into a PC. On this Buletooth shield, jumper setting should be: BT-TX to Digital 7, BT-RX to digital 6, and the mode switch to lower position.
Copy and paste the following host code, load into Arduino.

<syntaxhighlight lang="c">

  1. include <SoftwareSerial.h>
  2. define RxD 7
  3. define TxD 6

SoftwareSerial BlueToothSerial(RxD,TxD);

void Test_BlueTooth() {

  unsigned char t=0;
  String RXD = "";
  Serial.println("Test BlueTooth ...");
  BlueToothSerial.print("AT\r\n");  
  delay(100);
  while(BlueToothSerial.available()>0)
  {    
     RXD +=  char( BlueToothSerial.read() );
     delay(1);
  } 
  do{
    t++;
    delay(400);
    Serial.println("Test Failed ! Retrying ...");
  }while( ((RXD[0]!='O')&&(RXD[1]!='K'))&&(t<5));  
  if(t<5) Serial.println("Test Successful !\r\n");
  else { Serial.println("Retry Failed !"); while(1); }

}

void sendBlueToothCommand(char *Command) {

 BlueToothSerial.print(Command);
 Serial.print(Command); 
 delay(100);
 while(BlueToothSerial.available())
 {    
    Serial.print(char(BlueToothSerial.read())); 
 }

}

void setupBlueTooth() {

 Serial.println("Bluetooth Initialization ...");      
 sendBlueToothCommand("AT+NAME=Master\r\n");
 sendBlueToothCommand("AT+ROLE=1\r\n");// 1:Master   0:Slave
 sendBlueToothCommand("AT+PSWD=1234\r\n");
 sendBlueToothCommand("AT+UART=38400,0,0\r\n");
 sendBlueToothCommand("AT+CMODE=1\r\n");
 sendBlueToothCommand("AT+INIT\r\n");
 sendBlueToothCommand("AT+PAIR=12,11,230317,10\r\n");//slave address 
 for(int i=0;i<5;i++) delay(1000);
 BlueToothSerial.flush();
 Serial.println("Bluetooth Initialized Successfully !\r\n");

}

void setup() {

  Serial.begin(38400);     
  BlueToothSerial.begin(38400); 
  delay(500);
  Test_BlueTooth();  
  setupBlueTooth();

}

void loop() {

 if(BlueToothSerial.available())
 {
    Serial.print(char(BlueToothSerial.read()));
 }
 if(Serial.available())
 {
    BlueToothSerial.print(char(Serial.read()));
 }      

}

</syntaxhighlight>

After the code is uploaded to Arduino. Navigate to X-CTU, and open the com port of the host Bluetooth shield. The baud rate setting is still 38400/0/8/N/1. At this moment, LED D1 will blink fast (with a period of 0.4 seconds), and the serial port will output something as the following:

Bluetoothshield host slave 6.jpg

When the host and slave are connected, both host and slave will block slowly (with a period of around 2 seconds). Move the mode switch to upper position 'S'. Now, the red LEDs, LED-D2 on both Bluetooth shields will be on. It means that they are paired successfully, and we can start data communication.

Bluetoothshield host slave 7.jpg

Bluetoothshield host slave 8.jpg

Bluetoothshield host slave 9.jpg

Bluetooth shield communicates to Android Smartphone

  • Take one Bluetooth shield and do the following:
Select the Bluetooth shield communication port using jumpers: BT_RX is connected to D6 of Digital-6, BT_TX is connected to Digital-7. Move the mode selection switch to lower position so that Bluetooth module will enter into AT command mode.

Bluetoothshield host slave 1.jpg

Install Bluetooth shield on the Arduino Uno,and plung Arduino into PC, LED D1 on Bluetooth shield will start blinking.
Copy and paste the following sample code and download to Arduino:

<syntaxhighlight lang="c">

  1. include <SoftwareSerial.h>
  2. define RxD 7
  3. define TxD 6

SoftwareSerial BlueToothSerial(RxD,TxD); char flag=1; void Test_BlueTooth() {

  unsigned char t=0;
  String RXD = "";
  Serial.println("Test BlueTooth ...");
  BlueToothSerial.print("AT\r\n");  
  delay(100);
  while(BlueToothSerial.available()>0)
  {    
     RXD +=  char( BlueToothSerial.read() );
     delay(1);
  } 
  do{
    t++;
    delay(400);
    Serial.println("Test Failed ! Retrying ...");
  }while( ((RXD[0]!='O')&&(RXD[1]!='K'))&&(t<5));  
  if(t<5) Serial.println("Test Successful !\r\n");
  else { Serial.println("Retry Failed !"); while(1); }

}

void sendBlueToothCommand(char *Command) {

 BlueToothSerial.print(Command);
 Serial.print(Command); 
 delay(100);
 while(BlueToothSerial.available())
 {    
    Serial.print(char(BlueToothSerial.read())); 
 }

}

void setupBlueTooth() {

 Serial.println("Bluetooth Initialization ...");      
 sendBlueToothCommand("AT+NAME=LinkSprite\r\n");
 sendBlueToothCommand("AT+ROLE=0\r\n");
 sendBlueToothCommand("AT+CMODE=0\r\n");
 sendBlueToothCommand("AT+PSWD=1234\r\n");
 sendBlueToothCommand("AT+UART=38400,0,0\r\n");
 delay(500);
 Serial.println("Bluetooth Initialized Successfully !\r\n");
 do{
   if(Serial.available())
   {
     if( Serial.read() == 'S')
     {
       sendBlueToothCommand("AT+RESET\r\n");
       flag = 0;
     }
   }
 }while(flag);

}

void setup() {

  Serial.begin(38400);     
  BlueToothSerial.begin(38400); 
  delay(500);
  Test_BlueTooth();  
  setupBlueTooth();

}

void loop() {

   if(BlueToothSerial.available())
   {
     Serial.print(char(BlueToothSerial.read()));
   }
   if(Serial.available())
   {
     BlueToothSerial.print(char(Serial.read()));
   }	    

}

</syntaxhighlight>

Launch X-CTU to open the COM port, configure the baud rate to be 38400/0/8/N/1. LED-D1 on Bluetooth shield will start to blink at a period of 2 seconds. At the same time, we will see the following output on serial port: