Difference between revisions of "GPS Shield With SD Card Slot for Arduino V2.0 B"
(Created page with " File:GPS-V2B-01.jpg") |
|||
(21 intermediate revisions by 3 users not shown) | |||
Line 1: | Line 1: | ||
+ | == Introduction == | ||
+ | Arduino GPS shield is a GPS module breadout board designed for Global Positioning System receiver with SD interface. It is easy to use for recording the position data into SD card. | ||
− | [[File:GPS-V2B-01.jpg]] | + | [[File:N94DG WITHOUT PACKAGED FRONT.jpg | 640px]] |
+ | |||
+ | [[File:N94DG WITHOUT PACKAGED BACK.jpg|640px]] | ||
+ | |||
+ | |||
+ | == Features == | ||
+ | *With SD interface | ||
+ | *Active antenna design with high receive sensitivity, compatible normal antenna | ||
+ | *Extremely fast time to first fix at low signal level | ||
+ | *UART interface | ||
+ | *Operation temperature: -40℃ ~ +85℃ | ||
+ | |||
+ | |||
+ | == Application Ideas == | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | == Cautions == | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | == Schematic == | ||
+ | *[https://s3.amazonaws.com/linksprite/Shields/GPS+shield/arduino_gps_sd_V2-B.pdf Schematics] | ||
+ | |||
+ | == Specification == | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | == Pin definition and Rating == | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | == Mechanic Dimensions == | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | == Usage == | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | === Hardware Installation === | ||
+ | |||
+ | Install GPS SD Shield V2-B onto Arduino Uno, and use jumpers to short TX and MRX, RX and MTX. In this way, the MCU talks to the GPS module. | ||
+ | |||
+ | [[File:HW-GPS-V2B-01.jpg | 400px ]] | ||
+ | |||
+ | === Programming === | ||
+ | |||
+ | ==== Test GPS module ==== | ||
+ | |||
+ | <syntaxhighlight lang="c"> | ||
+ | |||
+ | void setup() | ||
+ | { | ||
+ | Serial.begin(9600); | ||
+ | } | ||
+ | void loop() | ||
+ | { | ||
+ | if (Serial.available() > 0) | ||
+ | { | ||
+ | Serial.print(char(Serial.read())); | ||
+ | } | ||
+ | } | ||
+ | |||
+ | </syntaxhighlight> | ||
+ | |||
+ | Compile and execute: | ||
+ | |||
+ | |||
+ | [[File:HW-GPS-V2B-02.jpg | 400px]] | ||
+ | |||
+ | ==== Test SD card ==== | ||
+ | |||
+ | It can use the built-in SD card example code in Arduino IDE. | ||
+ | |||
+ | |||
+ | [[File:HW-GPS-V2B-03.jpg | 400px ]] | ||
+ | |||
+ | |||
+ | We can observe the date being written into SD card through serial port. | ||
+ | |||
+ | |||
+ | [[File:HW-GPS-V2B-04.jpg | 400px ]] | ||
+ | |||
+ | == FAQ == | ||
+ | |||
+ | == Support == | ||
+ | |||
+ | If you have questions or other better design ideas, you can go to our [http://www.linksprite.com/forum/index.php forum] to discuss or creat a ticket for your issue at [http://www.linksprite.com/support/ linksprite support]. | ||
+ | |||
+ | == Resources == | ||
+ | |||
+ | *[http://linksprite.com/wiki/index.php5?title=GPS_module_SKM58 SKM58 Product Page] | ||
+ | *[http://tronixstuff.com/2014/01/15/tutorial-arduino-mediatek-3329-gps/ John Boxall's Tutorial] | ||
+ | |||
+ | == How to buy == | ||
+ | Here to buy GPS Shield With SD Card Slot for Arduino V2.0 B on [http://store.linksprite.com/gps-shield-with-sd-slot-for-arduino-v2-b/ store] | ||
+ | |||
+ | == See Also == | ||
+ | |||
+ | Other related products and resources. | ||
+ | |||
+ | == Licensing == | ||
+ | |||
+ | This documentation is licensed under the Creative Commons [http://creativecommons.org/licenses/by-sa/3.0/ Attribution-ShareAlike License 3.0] Source code and libraries are licensed under [http://www.gnu.org/licenses/gpl.html GPL/LGPL], see source code files for details. |
Latest revision as of 01:45, 12 October 2015
Contents
Introduction
Arduino GPS shield is a GPS module breadout board designed for Global Positioning System receiver with SD interface. It is easy to use for recording the position data into SD card.
Features
- With SD interface
- Active antenna design with high receive sensitivity, compatible normal antenna
- Extremely fast time to first fix at low signal level
- UART interface
- Operation temperature: -40℃ ~ +85℃
Application Ideas
Cautions
Schematic
Specification
Pin definition and Rating
Mechanic Dimensions
Usage
Hardware Installation
Install GPS SD Shield V2-B onto Arduino Uno, and use jumpers to short TX and MRX, RX and MTX. In this way, the MCU talks to the GPS module.
Programming
Test GPS module
<syntaxhighlight lang="c">
void setup() {
Serial.begin(9600);
} void loop() {
if (Serial.available() > 0) { Serial.print(char(Serial.read())); }
}
</syntaxhighlight>
Compile and execute:
Test SD card
It can use the built-in SD card example code in Arduino IDE.
We can observe the date being written into SD card through serial port.
FAQ
Support
If you have questions or other better design ideas, you can go to our forum to discuss or creat a ticket for your issue at linksprite support.
Resources
How to buy
Here to buy GPS Shield With SD Card Slot for Arduino V2.0 B on store
See Also
Other related products and resources.
Licensing
This documentation is licensed under the Creative Commons Attribution-ShareAlike License 3.0 Source code and libraries are licensed under GPL/LGPL, see source code files for details.