Difference between revisions of "Tilt Sensor"

From LinkSprite Playgound
Jump to: navigation, search
(Module specifications)
(Adjustable coupling)
 
(9 intermediate revisions by 2 users not shown)
Line 1: Line 1:
 
== Overview ==
 
== Overview ==
  
Based on the SW-460D ball switch digital module, the use of steel ball characteristics, through the action of gravity that ball to low rolling, thus making the switch closed or disconnect, so also can be used as a simple angle sensor use.
+
A tilt sensor is a simplified accelerometer.  It is a switch that can detect basic motion/orientation. The metal tube has a little metal ball that rolls around in it. When it is tilted upright, the ball rolls onto the contacts sticking out of end and shorts them together.  
  
Ball switch digital input module, and arduino special sensor expansion board combination, will be able to realize the very interesting interactive works, than using mercury switch more safety.
+
Shown in Figure 6.1 is the tile sensor SW-460D.  The electric characteristics of this sensor are listed in Table 6.1. The minimum tilt angel of this sensor is 2-5°.
  
== Specifications ==
+
[[File:tilt sensor.jpg | 400px]]
  
=== Specificaitons of Quality ===
+
===Adjustable coupling===
:*Working voltage: 3.3/5V DC
+
**[http://linksprite.com/wiki/index.php5?title=Sensors_Pack_for_Arduino Sensors Pack for Arduino] [KIT_SENPACK]
:*Interface types: Digital interface
 
:*2.54mm general interface
 
:*Module conduction angle:2~5°
 
  
=== Module specifications ===
+
== Specifications ==
 
 
{| class="wikitable" border="1"
 
|-
 
! align="center" style="width:200px" |Items
 
! align="center" style="width:200px" |Min
 
|-
 
| align="center" style="width:200px" |PCB Size
 
| align="center" style="width:200px" |2.5cm*2.7cm
 
|-
 
| align="center" style="width:200px" |Interface
 
| align="center" style="width:200px" |2.54mm pitch pin header
 
|-
 
| align="center" style="width:200px" |IO structure
 
| align="center" style="width:200px" |IN, NC, VCC, GND
 
|-
 
| align="center" style="width:200px" |VCC
 
| align="center" style="width:200px" |3/5V
 
|}
 
 
 
[[File:Tilt PCB.jpg | 400px]]
 
  
 
=== Characteristics ===
 
=== Characteristics ===
  
 
{| class="wikitable" border="1"
 
{| class="wikitable" border="1"
|+align="center" |Electrical Characteristics
+
|+align="center" |SW-460D Electrical Characteristics
 
|-
 
|-
! align="center" style="width:200px" |Model
+
! align="center" style="width:150px" |Voltage
! align="center" style="width:200px" |Voltage
+
! align="center" style="width:150px" |Current
! align="center" style="width:200px" |Current
 
 
! align="center" style="width:200px" |Conduction Time
 
! align="center" style="width:200px" |Conduction Time
 
! align="center" style="width:200px" |Path Resistance
 
! align="center" style="width:200px" |Path Resistance
Line 48: Line 24:
 
! align="center" style="width:200px" |Resistance To Temperature
 
! align="center" style="width:200px" |Resistance To Temperature
 
|-  
 
|-  
| align="center" style="width:200px" |SW-460D
+
| align="center" style="width:150px" |12V
| align="center" style="width:200px" |12V
+
| align="center" style="width:150px" |5mA
| align="center" style="width:200px" |5mA
 
 
| align="center" style="width:200px" |20mS
 
| align="center" style="width:200px" |20mS
 
| align="center" style="width:200px" |>10M omh
 
| align="center" style="width:200px" |>10M omh
Line 59: Line 34:
 
== Schematic ==
 
== Schematic ==
  
[[File:schematic of tilt.jpg]]
+
[[File:schematic of tilt.jpg | 400px]]
 +
 
 +
==  Example Project ==
 +
 
 +
===Hardware Preparation ===
 +
 
 +
The following hardware is needed in this project.
 +
 
 +
:*An Arduino Duemilanove board or compatible Arduino controller
 +
:*1 tilt sensor
 +
:*1 Prototyping Shield
 +
:*1 mini breadboard
 +
:*A 4-pin pitch pin header
 +
:*A resistor and a capacitor
 +
:*A few jumper wires
  
== Programming ==
+
=== Programming ===
 
The program below uses the tilt sensor to control the LED.
 
The program below uses the tilt sensor to control the LED.
  

Latest revision as of 10:04, 19 August 2014

Overview

A tilt sensor is a simplified accelerometer. It is a switch that can detect basic motion/orientation. The metal tube has a little metal ball that rolls around in it. When it is tilted upright, the ball rolls onto the contacts sticking out of end and shorts them together.

Shown in Figure 6.1 is the tile sensor SW-460D. The electric characteristics of this sensor are listed in Table 6.1. The minimum tilt angel of this sensor is 2-5°.

Tilt sensor.jpg

Adjustable coupling

Specifications

Characteristics

SW-460D Electrical Characteristics
Voltage Current Conduction Time Path Resistance Open Circuit Resistance Resistance To Temperature
12V 5mA 20mS >10M omh 10M omh 100°C

Schematic

Schematic of tilt.jpg

Example Project

Hardware Preparation

The following hardware is needed in this project.

  • An Arduino Duemilanove board or compatible Arduino controller
  • 1 tilt sensor
  • 1 Prototyping Shield
  • 1 mini breadboard
  • A 4-pin pitch pin header
  • A resistor and a capacitor
  • A few jumper wires

Programming

The program below uses the tilt sensor to control the LED.

Sample code:

<syntaxhighlight lang="c">

int ledPin = 13; // Connect LED to pin 13 int switcher = 3; // Connect Tilt sensor to Pin3

void setup() {

 pinMode(ledPin, OUTPUT);      // Set digital pin 13 to output mode
 pinMode(switcher, INPUT);       // Set digital pin 3 to input mode

} void loop() {

  if(digitalRead(switcher)==HIGH) //Read sensor value
    { 
       digitalWrite(ledPin, HIGH);   // Turn on LED when the sensor is tilted
    }
  else
    {
       digitalWrite(ledPin, LOW);    // Turn off LED when the sensor is not triggered
    }

}

</syntaxhighlight>